642-902 Q&A – Implement an EIGRP based solution (36-40)

Section1 – Implement an EIGRP based solution, given a network design and a set of requirements

QUESTION NO: 36
Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summarization is enabled on routers R2 and R3, but it is disabled on router R1. Which two EIGRP routes will be seen in the routing table of router R3? (Choose two.)

image
A. 10.0.0.0/8
B. 172.16.10.0/24
C. 172.16.0.0/24
D. 10.10.10.0/24
E. 172.16.0.0/16
F. 10.10.0.0/16
Answer: D,E

QUESTION NO: 37
Refer to the exhibit. ROUTE.com has just implemented this EIGRP network. A network administrator came to you for advice while trying to implement load balancing across part of their EIGRP network.

image
If the variance value is configured as 2 on all routers and all other metric and K values are configured to their default values, traffic from the Internet to the data center will be load balanced across how many paths? Select the best response.
A. 1
B. 2
C. 3
D. 4
E. 5
Answer: C

QUESTION NO: 38
EIGRP has been configured to operate over Frame Relay multipoint connections. What should the bandwidth command be set to?
A. the CIR rate of the lowest speed connection multiplied by the number of circuits
B. the CIR rate of the lowest speed connection
C. the CIR rate of the highest speed connection
D. the sum of all the CIRs divided by the number of connections
Answer: A
Explanation:
If the multipoint network has different speeds allocated to the VCs, take the lowest CIR and simply multiply it by the number of circuits. This is because in Frame-relay all neighbors share the bandwidth equally, regardless of the actual CIR of each individual PVC, so we have to get the lowest speed CIR rate and multiply it by the number of circuits. This result will be applied on the main interface (or multipoint connection interface).

QUESTION NO: 39
Refer to the exhibit. You are the network administrator of the Route.com company. You have been tasked to implement a hub and spoke EIGRP topology over Frame Relay to provide connectivity between the networks at headquarters and all 300 spokes. Before you begin the actual implementation, which three pieces of information are more important to know than the others? (Choose three.)

image
A. the Committed Information Rate of all the Frame Relay PVCs
B. the Cisco IOS version running on all the routers
C. the router model number of all the spoke routers
D. the number of HQ networks connected behind the headquarter routers
E. the routing policy, such as whether or not the spokes can be used as backup transient point between the two headquarter routers
Answer: A,B,E

QUESTION NO: 40
Refer to the exhibit. Router R1 is connected to networks 172.16.1.0 /26 and 172.16.1.64 /27. On the basis of the partial output in the exhibit, which statement is true?

image
A. Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised.
B. Router R1 will advertise both routes.
C. Router R1 should be reconfigured with an ACL instead of an ip prefix-list command.
D. Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.
Answer: D

Lead2pass Testking Pass4sure Actualtests Others
$99.99 $124.99 $125.99 $189 $29.99-$49.99
Up-to-Dated
Real Questions
Error Correction
Printable PDF
Premium VCE
VCE Simulator
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back

2 thoughts on “642-902 Q&A – Implement an EIGRP based solution (36-40)

  1. Question NO: 40

    There is a typo in Answer D? Should be “deny the 172.16.1.64/27 route..”

Comments are closed.