642-902 Q&A – Implement an EIGRP based solution (41-45)

Section1 – Implement an EIGRP based solution, given a network design and a set of requirements

QUESTION NO: 41
Refer to the exhibit. When you examine the routing table of R1 and R4, you are not able to see the R1 Ethernet subnet on the R4 routing table. You are also not able to see the R4 Ethernet subnet on the R1 routing table.

image
Which configuration change should be made to resolve this issue? Select the routers where the configuration change will be required, and select the required EIGRP configuration command(s).
Choose two answers. Select 2 response(s).
A. R1 and R4
B. R2 and R3
C. ip summary-address eigrp 1 10.1.1.0 255.255.255.0 and ip summary-address eigrp 1
10.2.2.0 255.255.255.0
D. variance 2
E. eigrp stub connected
F. no auto-summary
Answer: B,F

QUESTION NO: 42
Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?

image
A. Issue the command bandwidth 224 on the physical interface.
B. Issue the command bandwidth 56 on the physical interface.
C. Issue the command bandwidth 224 on each subinterface.
D. Issue the command bandwidth 56 on each subinterface.
Answer: A

QUESTION NO: 43
Which two routing protocols require a metric to be configured when redistributing routes from other protocols? (Choose two.)
A. RIP
B. BGP
C. IS-IS
D. OSPF
E. EIGRP
Answer: A,E
Explanation:
Metrics must be set manually via configuration when redistributing into RIP and EIGRP, whereas OSPF uses a default value of 20.
Example:

EIGRP
router eigrp 1
redistribute ospf 1 metric 1544 5 255 1 1500
redistribute rip metric 1544 5 255 1 1500
network 15.0.0.0
RIP
router rip
version 2
redistribute eigrp 1 metric 2
redistribute ospf 1 metric 3
network 16.0.0.0

QUESTION NO: 44
Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EIGRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause of the problem? Select the best response.

image
A. The no auto-summary command needs to be added under router eigrp 1.
B. The subnets keyword was not included in the redistribute command under router ospf 1.
C. The metric specified for the redistributed EIGRP routes is too large; making the EIGRP routes unreachable by router A.
D. The default-information originate command needs to be added under router ospf 1.
E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distance than OSPF.
Answer: B

QUESTION NO: 45
Refer to the exhibits. Router B should advertise the network connected to the E0/0/0 interface to router A and block all other network advertisements. The IP routing table on router A indicates that it is not receiving this prefix from router B. What is the probable cause of the problem? Select the best response.

image
A. An access list on router B is causing the 192.168.3.16/28 network to be denied.
B. An access list on router B is causing the 192.168.3.32/28 network to be denied.
C. The distribute list on router B is referencing a numbered access list that does not exist on router B.
D. The distribute list on router B is referencing the wrong interface.
Answer: A

Lead2pass Testking Pass4sure Actualtests Others
$99.99 $124.99 $125.99 $189 $29.99-$49.99
Up-to-Dated
Real Questions
Error Correction
Printable PDF
Premium VCE
VCE Simulator
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back