642-902 Q&A – Implement an EIGRP based solution (46-50)

Section1 – Implement an EIGRP based solution, given a network design and a set of requirements

QUESTION NO: 46
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2. What could be the cause of the problem?

image
A. The no auto-summary command has not been issued under the EIGRP process on both routers.
B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.
C. EIGRP cannot exchange routing updates with a neighbor’s router interface that is configured with two IP addresses.
D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
Answer: D

QUESTION NO: 47
Refer to the exhibit. A partial routing configuration is shown. Complete the configuration so that only the default-network is redistributed from EIGRP 190 into EIGRP 212. Which ACL statement completes the configuration correctly? Select the best response.

image
A. access-list 100 permit ip 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0
B. access-list 100 permit ip host 0.0.0.0 any
C. access-list 100 permit ip any host 0.0.0.0
D. A default-network cannot be redistributed between routing processes.
Answer: C

QUESTION NO: 48
Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:

*Mar 20 12:12:06: %DUAL-5-
NBRCHANGE: IP-EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active
*Mar 20 12:15:23: %DUAL-3-SIA:
Route 10.1.1.0/24 stuck-in-active state in IP-EIGRP 1. Cleaning up

The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network. Which statement best describes the reason for the error messages?
Select the best response.

image
A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.
B. Incorrect bandwidth configuration on router R5 prevents R2 from establishing neighbor adjacency.
C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .
D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .
Answer: C

QUESTION NO: 49
Refer to the exhibit. Which two statements are true? (Choose two.)

image
A. Router R1 will advertise connected and summary routes only.
B. The eigrp stub command will automatically enable summarization of routes on R2.
C. Router R1 is configured as a receive-only neighbor and will not send any connected, static, or summary routes.
D. The eigrp stub command prevents all routes except a default route from being advertised to R1.
E. The eigrp stub command prevents queries from being sent from R2 to R1.
F. Router R1 will advertise connected and static routes. The sending of summary routes will not be permitted.
Answer: A,E

QUESTION NO: 50
Refer to the exhibit. R1 accesses the Internet using E0/0. You have been asked to configure R1 so that a default route is generated to its downstream devices (191.0.0.1 and 192.0.0.1). Which commands would create this configuration? Select the best response.

image
A. router eigrp 190
redistribute static
!
ip route 0.0.0.0 0.0.0.0 Null0
B. ip default-network 20.0.0.0
C. router eigrp 190
redistribute static
!
ip route 0.0.0.0 255.255.255.255 Null0
D. ip default-network 20.20.20.0
Answer: A

Lead2pass Testking Pass4sure Actualtests Others
$99.99 $124.99 $125.99 $189 $29.99-$49.99
Up-to-Dated
Real Questions
Error Correction
Printable PDF
Premium VCE
VCE Simulator
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back

3 thoughts on “642-902 Q&A – Implement an EIGRP based solution (46-50)

Comments are closed.