642-902 Q&A – Implement a multi-area OSPF Network (16-20)

Section 2 – Implement a multi-area OSPF Network, given a network design and a set of requirements

QUESTION NO: 16
OSPF is enabled on router A. You execute the following command on router A and receive the accompanying output:

RouterA#ping 224.0.0.5 repeat 1
Type escape sequence to abort.
Sending 1, 100-byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:
Reply to request 0 from 10.100.100.1, 4 ms

10.100.100.1 is the IP address of a loopback interface on router A.

Continue reading

642-902 Q&A – Implement a multi-area OSPF Network (11-15)

Section 2 – Implement a multi-area OSPF Network, given a network design and a set of requirements

QUESTION NO: 11
Given the following partial configuration for Router A:

interface serial 0
ip address 10.1.1.1 255.255.255.0
ip ospf network point-to-multipoint
router ospf 7
network 10.1.1.0 0.0.0.255 area 0

Which two statements are correct? (Choose two.)

Continue reading

642-902 Q&A – Implement a multi-area OSPF Network (6-10)

Section 2 – Implement a multi-area OSPF Network, given a network design and a set of requirements

QUESTION NO: 6
Which two statements about route redistribution when implementing OSPF are true? Select 2 response(s).
A. Routes learned using any IP routing protocol can only be redistributed into non IP routing protocols.
B. OSPF can import routes learned using EIGRP, RIP, and IS-IS.
C. OSPF routes cannot be exported into EIGRP, RIP, and IS-IS.
D. At the interdomain level, OSPF cannot import routes learned using BGP.
E. OSPF routes can be exported into BGP.
Answer: B,E

Continue reading

642-902 Q&A – Implement a multi-area OSPF Network (1-5)

Section 2 – Implement a multi-area OSPF Network, given a network design and a set of requirements

QUESTION NO: 1
Refer to the exhibit. A network administrator wants to reduce the number of OSPF routes advertised from Area 1 into Area 2. As the router configuration specialist, what two things would you do to accomplish this goal? (Choose two.)

Continue reading

642-902 Q&A Index (Section1 – Implement an EIGRP based solution)

Section1 – Implement an EIGRP based solution, given a network design and a set of requirements

• Determine network resources needed for implementing EIGRP on a network
• Create an EIGRP implementation plan
• Create an EIGRP verification plan
• Configure EIGRP routing
• Verify EIGRP solution was implemented properly using show and debug commands
• Document results of EIGRP implementation and verification

Continue reading

642-902 Q&A – Implement an EIGRP based solution (66-68)

Section1 – Implement an EIGRP based solution, given a network design and a set of requirements

QUESTION NO: 66
You have implemented mutual route redistribution between OSPF and EIGRP on a border router.
When checking the routing table on one of the OSPF routers within the OSPF routing domain, you are seeing some, but not all of the expected routes. Which two things should you verify to troubleshoot this problem? Select 2 response(s).

Continue reading

642-902 Q&A – Implement an EIGRP based solution (56-60)

Section1 – Implement an EIGRP based solution, given a network design and a set of requirements

QUESTION NO: 56
Which of the following settings do not prevent two potential OSPF neighbors from becoming neighbors?
A. The interface used to connect to that neighbor being passive in the OSPF process
B. Duplicate OSPF router IDs
C. Mismatched dead timers
D. IP addresses of 10.1.1.1/24 and 10.2.2.2/24
E. Mismatched OSPF process IDs

Continue reading

Pages: 1 2 ... 317 318 319 320 321 322 323 324