CCNP ROUTE

642-902 Q&A – Implement a multi-area OSPF Network (56-60)

Section 2 – Implement a multi-area OSPF Network, given a network design and a set of requirements

QUESTION NO: 56
When learning a new route, if a LSA received is not found in the topological database, what will an internal OSPF router do?
A. The sequence numbers are checked, and if the LSA is valid it is entered into the topology database.
B. The LSA is placed in the topological database and an acknowledgement is sent to the transmitting router.
C. The LSA is dropped and a message is sent to the transmitting router.
D. The LSA is flooded immediately out of all the OSPF interfaces, except the interface from which the LSA was received.
Answer: D

Continue reading

642-902 Q&A – Implement a multi-area OSPF Network (51-55)

Section 2 – Implement a multi-area OSPF Network, given a network design and a set of requirements

QUESTION NO: 51
A network administrator has enabled OSPF across an NBMA network and has issued the command ip ospf network nonbroadcast. Given those facts, which two statements are true? (Choose two.)
A. DR and BDR elections will occur.
B. DR and BDR elections will not occur.
C. All routers must be configured in a fully meshed topology with all other routers.
D. The neighbor command is required to build adjacencies.
E. Interfaces will automatically detect and build adjacencies with neighbor routers.
Answer: AD

Continue reading

642-902 Q&A – Implement a multi-area OSPF Network (46-50)

Section 2 – Implement a multi-area OSPF Network, given a network design and a set of requirements

QUESTION NO: 46
Refer to the exhibit. ROUTE.com is planning to implement a secure OSPF network to support traffic between clients on the 172.16.10.0/24 network and the file server on the 172.16.20./24 network. You have been asked to review the implementation and verification plans for this OSPF project.
Which statement about the plan is true? Select the best response.

Continue reading

642-902 Q&A – Implement a multi-area OSPF Network (41-45)

Section 2 – Implement a multi-area OSPF Network, given a network design and a set of requirements

QUESTION NO: 41
What is the best order for choosing the Router-ID in ospf?
A. high loopback interface address, high physical interface address, Router ID command
B. high loopback interface address, Router ID command, high physical interface address
C. Router ID command, high loopback interface address, high physical interface address
D. Router ID command, high physical interface address, high loopback interface address
E. high physical interface address, high loopback interface address, Router ID command
Answer: C

Continue reading

CCNP ROUTE 642-902 Self-Study Resources List

In this post will provide the CCNP ROUTE 642-902 self-study resources, it will help you study and pass the exam. By the way, if you have other more resources, plz share with us.

The ROUTE 642-902 exam will certify that the successful candidate has the knowledge and skills necessary to use advanced IP addressing and routing in implementing scalable and secure Cisco ISR routers connected to LANs and WANs.  The exam also covers configuration of secure routing solutions to support branch offices and mobile workers.

Continue reading

What is CCNP 642-902 ROUTE Certification?

CCNP Route (642-902 ) exam is a one of the professional level exam from CISCO. CCNA is pre requisition for this exam. This CISCO exam replaced the old BSCI (642-901). This exam will help to deeply understanding the concepts of Routing . This exam Associated certification not only for CCNP it will help for CCIP and CCDP . Exam duration of the exam is 120 minutes. You have to answer 52 question.

The ROUTE 642-902 exam will certify that the successful candidate has the knowledge and skills necessary to use advanced IP addressing and routing in implementing scalable and secure Cisco ISR routers connected to LANs and WANs. The exam also covers configuration of secure routing solutions to support branch offices and mobile workers.

Continue reading