Section1 – Implement an EIGRP based solution, given a network design and a set of requirements
• Determine network resources needed for implementing EIGRP on a network
• Create an EIGRP implementation plan
• Create an EIGRP verification plan
• Configure EIGRP routing
• Verify EIGRP solution was implemented properly using show and debug commands
• Document results of EIGRP implementation and verification
Section1 – Implement an EIGRP based solution, given a network design and a set of requirements
QUESTION NO: 66
You have implemented mutual route redistribution between OSPF and EIGRP on a border router.
When checking the routing table on one of the OSPF routers within the OSPF routing domain, you are seeing some, but not all of the expected routes. Which two things should you verify to troubleshoot this problem? Select 2 response(s).
Section1 – Implement an EIGRP based solution, given a network design and a set of requirements
QUESTION NO: 61
Based on the exhibited output, which three statements are true? (Choose three.)
Section1 – Implement an EIGRP based solution, given a network design and a set of requirements
QUESTION NO: 56
Which of the following settings do not prevent two potential OSPF neighbors from becoming neighbors?
A. The interface used to connect to that neighbor being passive in the OSPF process
B. Duplicate OSPF router IDs
C. Mismatched dead timers
D. IP addresses of 10.1.1.1/24 and 10.2.2.2/24
E. Mismatched OSPF process IDs
Section1 – Implement an EIGRP based solution, given a network design and a set of requirements
QUESTION NO: 51
Refer to the exhibit. Routers R1 and R2 are running EIGRP and have converged. On the basis of the information that is presented, which statement is true?
Section1 – Implement an EIGRP based solution, given a network design and a set of requirements
QUESTION NO: 46
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2. What could be the cause of the problem?
Section1 – Implement an EIGRP based solution, given a network design and a set of requirements
QUESTION NO: 41
Refer to the exhibit. When you examine the routing table of R1 and R4, you are not able to see the R1 Ethernet subnet on the R4 routing table. You are also not able to see the R4 Ethernet subnet on the R1 routing table.
Section1 – Implement an EIGRP based solution, given a network design and a set of requirements
QUESTION NO: 36
Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summarization is enabled on routers R2 and R3, but it is disabled on router R1. Which two EIGRP routes will be seen in the routing table of router R3? (Choose two.)
Section1 – Implement an EIGRP based solution, given a network design and a set of requirements
QUESTION NO: 31
Which two statements about the EIGRP DUAL process are correct? (Choose two.) Select 2 response(s).
A. An EIGRP route will go active if there are no successors or feasible successors in the EIGRP topology table.
B. An EIGRP route will go passive if there are no successors in the EIGRP topology table.
C. DUAL will trigger an EIGRP query process while placing the flapping routes in the holddown state.
D. A feasible successor in the EIGRP topology table can become the successor only after all the query requests have been replied to.
E. The stuck in active state is caused when the wait for the query replies have timed out.
F. EIGRP queries are sent during the loading state in the EIGRP neighbor establishment process.
Answer: A,E
Section1 – Implement an EIGRP based solution, given a network design and a set of requirements
QUESTION NO: 26
Refer to the exhibit. EIGRP has been configured on all routers in the network. The command metric weights 0 0 1 0 0 has been added to the EIGRP process so that only the delay metric is used in the path calculations. Which router will R1 select as the successor and feasible successor for Network A?